Advanced Headlight Lens Restoration:

The lights are deep cleaned and degreased to remove as much surface contaminates as possible. The painted areas around the headlights are taped off to prevent any damage. We begin with a light to medium grit hand sanding process to remove surface issues on the lenses. This sanding step is repeated as needed and rinsed throughly.

A compound solution is applied to the lens to further help in removing any glazing and to clear up the sanding process. A machine polisher is used to work in the compound.  We buff out the headlight to begin to reveal its original look. At this point the lens should start to reveal its finished, crystal clear look. Finally a wax is applied to further protect, coat and polish the lights. This coating will also aid in preventing any future glazing and help prevent wear.

Est. Time 1 Hour

Engine Bay Basic Detail Includes:

Remove any debris, rinse and dry.

Est. Time 1/2 Hour

Engine Bay Detail Intermediate Includes:

Basic plus engine cleaner/degreaser applied, rinsed and dried.

Est. Time 45 Min.

Engine Bay Detail Advanced Includes:

Basic + Intermediate plus plastic protectant is added to the plastics for a wonderful shine and to promote the longevity of the trim.

Est. Time 1 Hour

Advanced “Wheels Off” Detail Includes:

Each wheel is removed from the vehicle to decontaminate every rim and tire as much as possible with our extensive detailing process. We start with a pre-rinse on the entire rim and tire to release as much stuck-on particles and dirt as possible. A degreaser is applied to remove dirt, grease and oil. A thorough rinse is done. An iron removal is applied to further decontaminate the rims of any additional fall-out then rinsed. We now apply a tar remover to remove and release any remaining staining on the rims. They are rinsed again. A rim friendly soapy-wash is done by hand to ensure any previously used product has been removed to achieve a maximum level of cleanliness. The final step in the cleaning process is where we run the clay bar over the entire rim to remove any lingering surface debris before the wheels are ready to be sealed with a protective wax coating. The wax coating gives the rims protection against future road grime, brake dust and water. (*A ceramic coating is available for an additional cost.) Lastly, a glossy tire shine is applied to the face of the tires to complete the freshly detailed look.

With the wheels removed from the vehicle, the wheel wells are pressure washed to remove as much debris as possible. A degreaser is applied to promote removal of stubborn dirt, grease and oil then rinsed clean. An iron decontamination remover is applied and rinsed to further clean the wheel well area. At this point, a foamy cleaning wash process begins with soft to hard brushes and microfiber towels to wipe the more delicate parts. The wheel wells are then rinsed down again and dried to prep for the final stage of applying our protective coating. This protective coating aids in giving the wheel wells a longer lifespan and helps with making future cleanings easier.

The wheels are finally put back on the vehicle after the tire pressure has been checked to meet vehicle specs.

Est. Time 2 – 3 Hours

* A durable ceramic coating is applied to the entire rim (front and back) while the wheels are off the vehicle. We will also coat the painted calipers (if any).

Est. add an additional 3-4 hours for curing of the ceramic coating

Advanced Convertible/Tonneau Top Detail Includes:

If your convertible top or tonneau cover is fabric, vinyl or even synthetic our cleaning and protection process will be safe. We use a cleaner that will penetrate deep into the fabric to remove stains and restore the material back to its original finish. We deep clean it throughly with soapy suds, soft, safe brushes, microfiber towels and to make sure we remove as much embedded contaminants as possible. It is then dried to set up for the protectant phase.

During the protectant phase separate coats of water repellent/protectant are applied to seal the convertible/tonneau top. This protectant stage creates a shield to repel liquids, dirt, stains and UV solar rays. This protectant bonds to the fabric fibers for a durable, lasting protection. It is non-toxic, safe and works great on all colors.

We will also clean the rear window of the vehicle. If the rear windows is a plastic, we will work to restore its life and luster. We work on removing the haze and yellowing that has accumulated and is preventing you from seeing out of it by using plastic cleaners that is safe for you and the car.

Est. Time 1-2 Hours

Basic Trim Detailing:

Want to rejuvenate your gray, faded, external black trim?

Have you been longing to bring back that amazing luster to your faded, dirty chrome or aluminum?

Then this detail is for you!

After the vehicle has been fully cleaned with our one of exterior washes to remove as much as the surface contaminants as possible we will proceed to bring the black back to your vinyl, plastic or rubber trim. We will carefully coat the entire vehicles trim with a microfiber applicator and our trim solution which will condition and protect it from the sun and the elements you throw at it.

We can polish the chrome or aluminum trim to bring that amazing sparkling shine back that you love so much.

All the window trims, bumpers, grills, mud flaps, roof rails, roof racks, bottom moldings, side mirrors, fender flairs, spare tire cover, running boards are protected. This will help bring back its original glorious black look or that amazing reflection you miss.

Est. Time 1-2 Hours

*The basic trim rejuvenation process is not a “painting process,” it is a conditioning/lotion application process. Repainting the trim maybe recommended depending on the severity of the ware.

Advanced Trim Detailing:

If the basic trim rejuvenating process is not enough and you want to take the detailing to another level we will repaint the trim.

After the vehicle has been fully cleaned with our one of exterior washes we will proceed to tape off the surrounding painted areas to protect it from any over spraying. We will lightly sand the area(s) to help with the bonding of the new paint. Black trim paint is applied in separate coats to bring the black back to the trim. After letting the paint dry and cure we will condition and protect it with a sealant.

Est. Time 3-5 Hours

Interior Detailing Basic Includes:

Safely gather and store all customers personal items left in the vehicle. Remove all trash, vacuum out the entire interior (trunk and floor mats included), wipe down and sanitize all surfaces (cup holders, vents, dash, steering wheel, gear shifter, center console, door panels, gas and brake pedals).

Est. Time 2 Hours

Interior Detail Intermediate Includes:

Basic plus sealant/protectant applied to any rubber, vinyl, plastic and/or wood trimmed surfaces.

Est. Time 3-4 Hours

Interior Detail Advanced Includes:

Basic + Intermediate plus shampoo the upholstery, carpet, floor mats and seats, if cloth.  Cleaned and conditioned, if leather.

Est. Time 4-6 Hours